Pressure Transducer
Load Cell
Instrumentation
Custom Machining
Custom Transducers
 

Universal Differential Pressure Transducer

   
Model: UVD
  • Ranges from 0-50 Psid to 0-750 Psid
  • Bonded Foil Strain Gage.
  • All-welded Stainless Steel Construction
  • Overload protected to 1500 psid from either side.
  • Line Pressure to 1500 psig.
  • Minimum Accuracy of 0.25 % FS
 
     
 
   
 
     
 
Products Specifications
Pressure Ranges 0-50 to 0-750 psid
Accuracy(min) 0.25 % FS
Non-Linearity +/-0.15 % FS
Hysteresis +/-0.10 % FS
Repeatability +/-0.05% FS
Sensitivity /Output 2 mV/V
Zero Setting +/- 1% FS
Zero shift with with Line pressure +/- 1.5 %F / 1500 psig
Resolution Infinite
   
Temperature, Operating           -65°F to 250°F (non-oil filled)
Temperature, Compensated 60°F to 160°F
Temperature Effect,  Zero +/- 0.5 %FS Nominal / 100°F
Temperature Effect,  Span +/- 1% Reading / 100°F
   
Strain Gages Type Bonded foil
Excitation(Calibrated) 10 VDC
Excitation(acceptable) up to 12 VDC or AC
Bridge Insulation Resistance 5000 megOhms
Bridge Resistance 350 Ohms Nominal
Shunt Calibrated Data included on calibration sheet
Wiring Code Red / Black…………+/- Excitation
White / Green………+/- Signal
Mating connector 15 ft Cable Poly urethane jacked cable
   
Electrical Terminations
  • Integral cable with 5 ft., 4 conductor, shielded, Poly urethane jacked cable.
  • Optional welded-on PTIH-10-6P (6 pins) Quick disconnect hermetic connector.
   
Media Gas or liquid
Maximum Line Pressure 1500 psig       
Maximum Overload protected 1500 psi (either side)
Pressure Connections  1/8-27NPT Inside Thread (2)
Tapped Mounting Holes (2 each) 1/4-28UNF x 5/16” deep (2)
Drain Ports 1/8-27 NPT inside thread (2)
Burst Pressure  
Wetted parts Material 17-4PH Stainless Steel
Weight 5.0 lbs
O-Ring Seals Viton Standard
Dead Volume 0.25 cubic inches
Case Material 17-4PH Stainless Steel
   
Diameter 3.00 Inches
Length 3.00 Inches
   
Optional High Level Outputs
with zero and span adjustments
+/- 5 VDC +/ 10 VDC with internal Shunt Calibration Resistor,
or 4-20mA Two Wire  (Specify)
 


 

 
                 
  Pressure Transducers   Load Cells   Load Cell Accessories   Services  
  High Precision   Compression Only   Base/Pull Plates   Strain Gauging  
  Miniature Flush Diaphragm   Tension Only   Load Buttons   Re-Calibration  
  Steam Sterilizers   Compression/ Tension   Tongue Shackle   Transducer/Repair  
  Flush Diaphragm   Miniature Load Cell   Yoke Shackle      
  Universal Pressure Transducer   Universal Load Cell          
  Universal Differential   Low Profile Load Cell          
      Thru Hole Design Load Cell          
      Internally Threaded Mini Donut          
             
 
                 
 

HOME | ABOUT US | PRODUCTS | SERVICES
SENSORWERKS©2016